H7AN-R6DM AC100-240
Type: H7AN-R6DM AC100-240
Function
1 Stage Preset Counter
Preset stages
1stages
Rated supply voltage
100 to 240 VAC 50/60 Hz
Operating voltage range
85% to 110% of the rated power supply voltage
Power consumption
Approx. 10 VA (at 100 VAC)
External power supply
12 VDC ±10% 80 mA (permissible ripple: 5%(p-p) Max.)
Counter (Count range)
0～999999
Counter (Max. counting speed)
30 Hz/5 kHz (switching) (Minimum counting input signal width: 16.7 ms (ON/OFF ratio: 1:1)/0.1 ms (ON/OFF ratio: 1:1))
Counter (Input mode)
Increment decrement or increment/decrement (switchable)
Counter (Output modes)
N / F / C / R / K / P / Q
Counter One-shot time)
0.1 to 1 s variable
Counter (Reset system)
External, manual, automatic and power reset (when set the SW3 for No memory backup)
Input signal
CP1 / CP2 / Reset
Input method
Voltage input
No-voltage input (Contact input）
Use a contact which can adequately switch 2.5 mA at 12 V.
Voltage input
Hight level: 5 to 30 VDC
Low level: 0 to 2 VDC
Input resistance: 4.7 kΩ
Minimum input signal width
External reset: 20 ms
Manual reset: 20 ms
Automatic reset: 100 to 1000 ms (C, R, P and Q mode)
Control output (Contact output)
SPDT
Switching capacity: 3 A at 250 VAC/30 VDC, resistive load (cos phi=1)
Minimum applicable load: 10 mA at 5 VDC (failure level:P reference value)
Control output (Solid-state output)
Output type: Transistor output (NPN open collector)
Output resistance: 1.5 kΩ
Switching capacity: 30 VDC max., 100 mA max.
Display method
7-segment LED
Digits
6digits
Character height
Count value: 8 mm (Red)
Zero suppression: Not provided
Prescaling function
Not provided
Key protection
Not provided
Teaching function
Not provided
Batch counting function
Not provided
Communications
Not provided
Memory backup
Non-volatile memory (Number of rewite: 1,000,000 operations min.)
Surrounding air temperature
Operating: -10 to 55 ℃
Storage: -25 to 65 ℃
Ambient humidity
Operating: 35 to 85%
Storage: 35 to 85%
Insulation resistance
100 MΩ min. (at 500 VDC)
Between current carrying terminals and exposed non-current carrying metal parts / Between non-continuous contacts
Dielectric withstand voltage
Between current carrying terminals and exposed non-current carrying metal parts:2000 VAC 50/60 Hz for 1 min
Between non-continuous contacts:750 VAC 50/60 Hz for 1 min
Impulse withstand voltage
Between power terminals:6.0 kV
Between current carrying terminals and exposed non-current carrying metal parts:6.0 kV
Noise immunity
Between power terminals:±2k V
Between input terminals:±500 V
Square-wave noise by noise simulator (Pulse width: 100 ns/1 µs, 1-ns rise)
Static immunity
±8 kV (malfunction), ±15 kV (destruction)
Vibration resistance （Destruction）
10 to 55 Hz, 0.375-mm single amplitude each in 3 directions for 2 h
Vibration resistance （Malfunction）
10 to 55 Hz, 0.25-mm single amplitude each in 3 directions for 10 min
Shock resistance （Destruction）
300 m/s**2, 3 times each in 6 directions (3 axes)
Shock resistance （Malfunction）
100 m/s**2, 2 times each in 6 directions
Mechanical life expectancy
10,000,000 operations min.
Electrical life expectancy
100,000 operations min. (3 A at 250 VAC, resistive load)
Degree of protection
Case front: JEM IP30
Mounting method
Flush mounting
External connection method
Screw terminal
Case color
Light gray (Munsell 5Y7/1)
Accessories
Mounting bracket
Weight
Approx. 360 g
| Function | 1 Stage Preset Counter |
|---|---|
| Preset stages | 1stages |
| Rated supply voltage | 100 to 240 VAC 50/60 Hz |
| Operating voltage range | 85% to 110% of the rated power supply voltage |
| Power consumption | Approx. 10 VA (at 100 VAC) |
| External power supply | 12 VDC ±10% 80 mA (permissible ripple: 5%(p-p) Max.) |
| Counter (Count range) | 0～999999 |
| Counter (Max. counting speed) | 30 Hz/5 kHz (switching) (Minimum counting input signal width: 16.7 ms (ON/OFF ratio: 1:1)/0.1 ms (ON/OFF ratio: 1:1)) |
| Counter (Input mode) | Increment decrement or increment/decrement (switchable) |
| Counter (Output modes) | N / F / C / R / K / P / Q |
| Counter One-shot time) | 0.1 to 1 s variable |
| Counter (Reset system) | External, manual, automatic and power reset (when set the SW3 for No memory backup) |
| Input signal | CP1 / CP2 / Reset |
| Input method | Voltage input |
| No-voltage input (Contact input） | Use a contact which can adequately switch 2.5 mA at 12 V. |
| Voltage input | Hight level: 5 to 30 VDC Low level: 0 to 2 VDC Input resistance: 4.7 kΩ |
| Minimum input signal width | External reset: 20 ms Manual reset: 20 ms Automatic reset: 100 to 1000 ms (C, R, P and Q mode) |
| Control output (Contact output) | SPDT Switching capacity: 3 A at 250 VAC/30 VDC, resistive load (cos phi=1) Minimum applicable load: 10 mA at 5 VDC (failure level:P reference value) |
| Control output (Solid-state output) | Output type: Transistor output (NPN open collector) Output resistance: 1.5 kΩ Switching capacity: 30 VDC max., 100 mA max. |
| Display method | 7-segment LED |
| Digits | 6digits |
| Character height | Count value: 8 mm (Red) Zero suppression: Not provided |
| Prescaling function | Not provided |
| Key protection | Not provided |
| Teaching function | Not provided |
| Batch counting function | Not provided |
| Communications | Not provided |
| Memory backup | Non-volatile memory (Number of rewite: 1,000,000 operations min.) |
| Surrounding air temperature | Operating: -10 to 55 ℃ Storage: -25 to 65 ℃ |
| Ambient humidity | Operating: 35 to 85% Storage: 35 to 85% |
| Insulation resistance | 100 MΩ min. (at 500 VDC) Between current carrying terminals and exposed non-current carrying metal parts / Between non-continuous contacts |
| Dielectric withstand voltage | Between current carrying terminals and exposed non-current carrying metal parts:2000 VAC 50/60 Hz for 1 min Between non-continuous contacts:750 VAC 50/60 Hz for 1 min |
| Impulse withstand voltage | Between power terminals:6.0 kV Between current carrying terminals and exposed non-current carrying metal parts:6.0 kV |
| Noise immunity | Between power terminals:±2k V Between input terminals:±500 V Square-wave noise by noise simulator (Pulse width: 100 ns/1 µs, 1-ns rise) |
| Static immunity | ±8 kV (malfunction), ±15 kV (destruction) |
| Vibration resistance （Destruction） | 10 to 55 Hz, 0.375-mm single amplitude each in 3 directions for 2 h |
| Vibration resistance （Malfunction） | 10 to 55 Hz, 0.25-mm single amplitude each in 3 directions for 10 min |
| Shock resistance （Destruction） | 300 m/s**2, 3 times each in 6 directions (3 axes) |
| Shock resistance （Malfunction） | 100 m/s**2, 2 times each in 6 directions |
| Mechanical life expectancy | 10,000,000 operations min. |
| Electrical life expectancy | 100,000 operations min. (3 A at 250 VAC, resistive load) |
| Degree of protection | Case front: JEM IP30 |
| Mounting method | Flush mounting |
| External connection method | Screw terminal |
| Case color | Light gray (Munsell 5Y7/1) |
| Accessories | Mounting bracket |
| Weight | Approx. 360 g |