H5CX-L8D-N
Type: H5CX-L8D-N
| Rated supply voltage | 24 VAC 50/60 Hz 12 to 24 VDC 20% max. |
|---|---|
| Operating voltage range | 85% to 110% of rated supply voltage (90% to 110% at 12 to24 VDC) |
| Power consumption | 5.1VA (at 24 VAC) 2.4W (at 24 VDC) |
| Time ranges（Number of ranges） | 10 |
| Time ranges | 0.001 s to 9.999 s / 0.01 s to 99.99 s / 0.1 s to 999.9 s / 1 s to 9999 s / 0.1 min to 999.9 min / 1 min to 9999 min / 0.1 h to 999.9 h / 1 h to 9999 h 1sec～99min59sec |
| Select method | Operation Key |
| Input signals | Signal, Reset |
| Input method | No-voltage input |
| No-voltage input（Solid state input） | ON impedance: 1 kΩ max. Leakage current: Approx. 12 mA ON residual voltage: 3 V max. OFF impedance: 100 kΩ min. (The DC voltage must be 30 VDC max.) |
| No-voltage input（Contact input） | Use contact which can adequately switch 5 mA at 10 V (The DC voltage must be 30 VDC max.) |
| No-voltage input（Applicable two-wire sensor） | Leakage current: 1.5 mA max. Switching capacity: 5 mA min. Residual voltage3.0 VDC max. Operating voltage: 10 VDC |
| Output modes | A (Signal ON delay1) A-1 (Signal ON delay2) A-2 (Power ON delay1) A-3 (Power ON delay2) b (Repeat cycle1) b-1 (Repeat cycle2) d (Signal OFF delay) E (Interval) F (Cumulative) Z (ON/OFF-duty adjustable flicker) S (Stopwatch) toff (Flicker OFF start1) ton (Flicker ON start1) toff-1 (Flicker OFF start2) ton-1 (Flicker ON start2) |
| Control output （Contact output） | Type: SPDT Switching capacities (Resistive load): 5 A at 250 VAC/30 VDC Minimum applicable load: 10 mA at 5 VDC (failure level: P Reference value) |
| One-shot output time | 0.01 to 99.99 s |
| Reset system | Power reset (depending on output mode) / Automatic reset (depending on output mode) / External reset / Manual reset |
| Power reset | Minimum power-opening time: 0.5 s (except for A-3, b-1, F, ton-1 and toff-1 mode) |
| Timer mode | Elapsed time (UP) and remaining time (DOWN) (selectable) |
| Display method | 7-segment negative transmissive LCD |
| Digit | 4 digit |
| Character height | Present value: 12 mm (Red) Set value: 6 mm (Green) |
| Key protect method | Key protect Switch |
| Memory backup method | EEP-ROM Number of rewite: 100,000 operations min. / Service life: 10 years min. |
| Ambient temperature | Operating: -10 to 55 ℃ When mount timer side by side: -10 to 50 ℃ Storag: -25 to 70 ℃ |
| Ambient humidity | Operating: 25 to 85%RH |
| Total accuracy | Accuracy of operating time and setting error (including temperature and voltage influences) Power-ON start: ±0.01% ±50 ms max. The values are based on the set value. Accuracy of operating time and setting error (including temperature and voltage influences) Signal start: ±0.005% ±30 ms max. The values are based on the set value. |
| Insulation resistance | 100 MΩ min. (at 500 VDC) Between current carrying terminals and exposed non-current carrying metal parts / Between non-continuous contacts |
| Dielectric strength | Between current carrying metal parts and non-current carrying metal parts: 2000 between control output and power/input circuit: 2000 Between non-continuous contacts: 1000 |
| Impulse withstand voltage | Between power terminals: 1.0 kV Between current carrying terminals and exposed non-current carrying metal parts: 1.5 kV |
| Noise immunity | Between power terminals: ±1.5 kV Between input terminals: ±600 V Square-wave noise by noise simulator (Pulse width: 100 ns/1 us, Rise: 1-ns) |
| Static immunity | Mulfunction: 8 kV, Destruction: 15 kV |
| Vibration resistance （Destruction） | 10 to 55 Hz, 0.75-mm single amplitude each in 3 directions for 2 h |
| Vibration resistance （Malfunction） | 10 to 55 Hz 0.35 mm single amplitude each in 3 directions for 10 min |
| Shock resistance （Destruction） | 300 m/s**2, 3 times each in 3 axes each directions |
| Shock resistance （Malfunction） | 100 m/s**2, 3 times each in 6 directions |
| Mechanical life | 10 million operations min. (under no load at 1,800 operations/h) |
| Electrical life | 100,000 operations min. (5 A at 250 VAC resistive load at 1800 operations/h) |
| Degree of protection | Panel surface: IEC IP66, UL508 Type 4X (indoors) (when using the Y92S-29 Waterproof Packing and Y92F-30 Flush Mounting Adapter) |
| Mounting method | Flush mounting / Surface mounting |
| External connection method | 8-pin round socket |
| Case color | Black (Munsell N1.5) |
| Accessory (sold separately) | Y92A-48F1: Soft Cover Y92A-48: Hard Cover Y92F-30: Flush mounting adapter Y92F-45: Flush mounting adapter Y92S-29: Waterproof rubber packing Y92P-CXT4S: Replacement Front Panel Y92P-CXT4G: Replacement Front Panel Y92P-CXT4B: Replacement Front Panel |
| Weight | 約115g |